- Home
- /Engineered Timber
Engineered Timber
Real timber top layer on stable engineered core. Premium Australian and European oak options.
Real timber top layer on stable engineered core. Premium Australian and European oak options.
Get your engineered timber flooring price per m² — free measure & quote.
An engineered board is built in layers. The top is real hardwood — usually European Oak — and underneath it sits a core of plywood laid in alternating directions. What you walk on, see and sand is timber. What holds it still is the engineering below.
That cross-layered core is the entire point. Solid timber takes on and gives up moisture with the seasons and moves as it does, which is why it needs expansion room and a timber subfloor. Because an engineered board’s layers pull against each other, it stays far closer to the size it was milled at. It is the same timber surface, on a base that argues with the weather instead of following it.
This is not a printed floor. Laminate and hybrid reproduce timber with a photographic layer; engineered is timber, with the grain, the colour variation and the ability to be refinished that only real wood has.
The honest answer depends on the room and the subfloor, not on which product is better made.
Choose engineered if you are laying over a concrete slab, if there is underfloor heating, or if the floor runs through a kitchen or a hallway that opens onto the garden. Most homes built or renovated in Melbourne in the last twenty years sit on a slab, which is why engineered has become the default rather than the alternative.
Choose solid if you have a timber subfloor, you are staying long term, and you want a floor that can be sanded back and made new again several times over. Our solid timber range covers that, and the full comparison is here.
One point worth being straight about: engineered is not a cheaper imitation of solid. A thick-wear-layer engineered board is a premium floor, and on a slab it is the better floor, not the compromise.
If you take one thing from this page, take this. The wear layer — sometimes called the top layer or veneer — is the depth of real hardwood above the core. It is the single number that separates a floor you will replace from a floor you will keep.
Across our engineered ranges the wear layer runs from about 1mm to 4mm, and most sit at 3mm. That figure matters because sanding a timber floor removes a little of the surface each time. A 3mm or 4mm layer can be sanded back and refinished, so a mark, a pet or a change of taste ten years from now is a job rather than a new floor. A 1mm layer cannot — it is a surface to be looked after, not restored.
You will see a board written as “14/3”: a 14mm board with a 3mm hardwood wear layer. The first number is how thick the whole board is; the second is how much of it is the timber you can sand. The second number is the one to compare.
Every range page on this site lists its own board thickness and wear layer, so you can check before you choose rather than after.
Two floors in the same oak can look like different materials depending on how the board is cut and finished.
Width. Our engineered boards run from about 120mm to 240mm, with 190mm the most common. A wider board shows more of the grain and puts fewer lines across a room, which makes an open living area feel calmer and larger. A narrower board puts more lines in and suits a period home, a hallway or a smaller room, where wide boards can feel heavy.
Length. Longer boards mean fewer end joins and a quieter-looking floor. It is a subtle thing in a photograph and very noticeable in a long hallway.
Finish. A matte or low-sheen lacquer hides dust, scuffs and footprints far better than a gloss and is what most people now choose. Brushed and oiled surfaces show the grain more and feel more like raw timber underfoot.
Pattern. Not every engineered floor is a straight plank. Ten of our engineered ranges are laid as herringbone, and there is a chevron range as well — the engineered herringbone guide explains what changes when you move from a plank to a pattern, in both the look and the fitting.
Living areas, bedrooms and hallways. This is engineered timber at its best, and where most of our floors go. It handles the daily traffic, and on a slab it will stay flat in a way a solid floor will not.
Kitchens and dining rooms. Used constantly and they look excellent, with one honest warning: engineered timber is real wood, so it is not waterproof. Spills want wiping up rather than leaving, and a leaking dishwasher is a serious problem. If that worries you more than the look does, hybrid flooring is the waterproof alternative that still reads as timber.
Bathrooms and laundries. No. Neither engineered nor solid timber belongs in a wet room, and we will tell you so rather than sell you one.
Over underfloor heating. Yes, and this is a real advantage over solid. Several of our ranges are rated for it, but compatibility depends on the range and the subfloor, so ask us about the specific floor rather than assuming.
Melbourne’s weather. Our swing from a damp winter to a dry northerly is exactly the movement engineered construction is built to resist. It is a large part of why the floor suits this city.
How it goes down. Engineered boards are either floated over an underlay — the boards lock together and rest on the subfloor — or glued directly to it. Floating is quicker and can be lifted again; direct stick feels more solid underfoot and is usually what we recommend over a slab. Which suits your home depends on the subfloor, and it is one of the things we check when we measure.
Before fitting. The boards should sit in the room for a few days before they are laid, so the timber settles to your home’s own humidity rather than the warehouse’s. This is not a formality — it is the step that prevents gaps appearing a month later.
Day to day. Sweep or vacuum with a floor head, and mop with a barely damp cloth rather than a wet one. Felt pads under furniture, and a mat at doors leading outside, prevent most of the marks a timber floor ever gets. No steam mops.
Years later. If the wear layer is 3mm or more, the floor can be sanded back and refinished rather than replaced — which is the quiet reason a good engineered floor works out well over a long time.
Get your engineered timber flooring price per m² — free measure & quote.
Love the parquet look?
Everything worth knowing before you choose an engineered floor — how it compares, which board to pick, and what each timber looks like.