Skip to main content
Solid timber is one piece of hardwood through the whole board — no core, no veneer, no backing layer. It is the floor people picture when they say “real timber”, and it is the only one you can sand back and refinish again and again, which is why a solid floor can outlast the people who laid it. Below you’ll find the Australian and imported species we carry, how solid compares with engineered, and where in a Melbourne home it belongs.

Get your solid timber flooring price per m² — free measure & quote.

What makes a floor solid timber

A solid board is milled from a single piece of hardwood, typically 19mm thick, with a tongue and groove along each edge. There is nothing underneath the surface you walk on but more of the same timber.

That is the whole difference, and everything else follows from it. Because the board is solid all the way down, the surface can be sanded back to bare wood and refinished — not once, but several times across the life of the floor. An engineered board has a hardwood veneer over a plywood core, so it can usually be refinished once, and a thin veneer not at all.

It also means the board behaves like the tree it came from. Solid timber takes on and gives up moisture with the seasons, which is why it is laid with expansion room and why it is not the right floor for a bathroom.

The species we carry

Species is the decision that matters most on a solid floor. It sets the colour, the grain, and how well the floor stands up to daily wear — and unlike a printed floor, what you choose is what you get, because the colour is the timber itself.

Australian hardwoods. Blackbutt is pale to golden with a fine, even grain — the most popular choice for lighter, modern interiors. Spotted Gum carries far more colour movement, from pale brown through to deep chocolate, often within the same board; we carry it in one, two and three strip layouts. Grey Ironbark and Red Ironbark are among the hardest floors available in Australia — ironbark is the choice when durability matters more than anything else. Tallowwood sits in the middle, a warm yellow-brown with a smooth, consistent look. Sydney Blue Gum is softer in tone, pink through to warm brown.

Imported hardwoods. Jatoba (Brazilian cherry) is a rich red-brown that deepens noticeably with light over the first year. Kempas is a warm orange-red, and Tauari is a pale, quiet, even-grained timber for people who want real hardwood without strong colour.

The grid above shows what we currently stock in each. Timber varies board to board by nature, so it is worth seeing a sample in your own light before you commit to a species.

Solid or engineered — which you should choose

This is the question we are asked most, and the honest answer depends on the room rather than on which product is better.

Choose solid if you are staying in the home long term and want a floor that can be sanded back and made new again decades from now. Over a timber subfloor, in living areas and bedrooms, solid is the floor that lasts longest and holds its character best.

Choose engineered if you are laying over a concrete slab, if you want wide boards without the seasonal movement, or if the floor runs through a kitchen. The plywood core is far more stable across Melbourne’s seasonal humidity swings, and it can be floated rather than nailed. Our engineered timber range covers that side, and there is a full comparison in our guide to engineered vs solid timber flooring.

Neither is a compromise. A solid floor in the right room will outlive an engineered one; an engineered floor in the wrong room for solid will outlive it comfortably. Cost usually comes into the decision too, and our guide to what engineered timber flooring costs in Melbourne sets out what moves the price either way.

Where solid timber belongs in a Melbourne home

Best suited to: living rooms, bedrooms, hallways, dining rooms, studies — dry rooms over a timber subfloor or battens, where the floor can be nailed or glued down properly.

Think carefully about: kitchens. Solid timber is used in kitchens often and looks superb, but spills need wiping up rather than leaving, and a dishwasher leak is a serious event rather than a mopping job.

Not suitable for: bathrooms, laundries, or anywhere below ground level. Solid timber and standing water do not belong together, and no finish changes that. If you want the timber look in a wet room, that is what hybrid flooring exists for.

On a concrete slab: possible, but it needs a moisture barrier and either battens or a full glue-down system, and the cost of that preparation is real. On a slab, engineered is usually the more sensible floor.

Fitting and looking after a solid floor

Solid boards are secret-nailed to a timber subfloor or battens, or glued down. They are not a floating floor and they are not a weekend job — the boards need to sit in the room for several days before laying so they settle to its humidity, and the expansion gap around the edges has to be right or the floor will move against itself later.

Boards can be supplied pre-finished, coated in the factory and ready to walk on the day they are laid, or raw and sanded and coated in place, which gives a seamless surface with no bevels between boards but adds several days and some dust to the job.

Day to day, care is simple: sweep or vacuum on a hard-floor setting, damp mop rather than wet, wipe up spills as they happen, felt pads under furniture, and a mat at the entry to stop grit coming in. Grit is what scratches timber floors, not water. Depending on the coating, a solid floor is re-coated every seven to ten years — and when it eventually looks tired, it is sanded back rather than replaced. That is the whole point of it.

Get your solid timber flooring price per m² — free measure & quote.

Solid timber flooring — frequently asked questions

How long does a solid timber floor last?
Longer than any other floor we sell. Because the board is solid hardwood the whole way through, it can be sanded back and refinished several times, so a well-looked-after solid floor commonly lasts 50 years or more — often longer than the building it was laid in.
Can solid timber go over concrete?
Yes, but it needs proper preparation — a moisture barrier and either battens or a full glue-down system. That preparation is a real cost, and on a slab an engineered floor is usually the more sensible choice. We will tell you honestly which suits your subfloor when we measure.
Which Australian hardwood is the hardest?
Grey Ironbark and Red Ironbark are among the hardest timbers flooring is made from anywhere. If you have large dogs or a very busy household and durability is the priority, ironbark is the species to ask about.
Is solid timber suitable for a kitchen?
It is used in kitchens regularly and looks excellent there, but it is not waterproof. Spills need wiping up rather than leaving, and a leaking appliance is a serious problem rather than an inconvenience. If the kitchen is the room you are worried about, hybrid flooring is the waterproof alternative.
How much does solid timber flooring cost in Melbourne?
It depends on the species, the board width and the state of your subfloor, and it is the most expensive timber option we carry. Rather than quote a number that turns out to be wrong for your home, we measure and give you a firm price — call us and we will arrange it.
Can I see the timber before I decide?
Yes, and with solid timber you should. Colour and grain vary board to board because it is a natural material, and showroom lighting is not your lighting. Come into the Blackburn South showroom, or we can get samples to you.

Free, no-obligation quote

Get a solid timber flooring quote

Tell us the rooms, the approximate area and your timeframe, and we'll come back with a price — free measure and quote.

Prefer to talk? Call 0475 588 816 · No spam, ever.